![]() ![]() The display powers on, but there is no data output on the screen. How can I get it to upload on the other Pro Minis? I have three Pro Minis in my possession and the code only downloads on one of them. I have also tried updating Arduino and my computer, as well as changing Pro Minis. I have searched through this forum community for solutions and have already tried burning the bootloader and confirming the correct port, board, processor, and programmer addresses. Maximum is 2048 bytes.Īvrdude: stk500_recv(): programmer is not respondingĪvrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x1bĪvrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x1bĪvrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x1bĪvrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x1bĪvrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x1bĪvrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x1bĪvrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x1bĪvrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x1bĪvrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x1bĪvrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x1bįailed uploading: uploading error: exit status 1 Global variables use 510 bytes (24%) of dynamic memory, leaving 1538 bytes for local variables. Sketch uses 7060 bytes (22%) of program storage space. we are not currently timing, so just chill triggers the end of the timing interval the magnet is close to the reed switch so insert a zero if number smaller than 10 Print class does not support fixed width formatting ![]() - Quick 3 blinks of backlight - no longer needed since no max time shark can be on line it is more as if the longer the shark is on the line, the more stressed it is likely to be that there is no max time a shark can be on the line originally I had "FREE SHARK " in () but I learned Lcd.print("MOTE SHARK TIMER") //prints that phrase on screen Lcd.setCursor(4,1) // moves LCD cursor to character 4, line 1 delay() // figure out the time max no longer need lcd.print(millis()/1000) // unsure if I need for settign up count up By default, the starting location is (0,0).lcd.setCursor(6,0) // sets cursor on character 6, line 0 The first argument of setCursor() specifies which column number, and the second specifies which row number. The positions on the screen are indexed starting with (0,0) in the top-left position. Lcd.begin(16,2) // initialize the lcd for 16 chars 2 lines, turn on backlight Serial.begin(9600) // Used to type in characters put your setup code here, to run once: sets up pin read mode and LCD display Unsigned long start_time // stores the start of the timing interval Int is_timing=0 // // 1 means we are timing the interval between triggers 0 means we are not we may also asign the address as lcd(0x3F, 16,2) sets the LCD address to Ox3F as well( programmingboss) im unsure if this address is for the 8-bit or the 4 bit we need the 4 bit Hd44780_I2Cexp lcd(0x3F) // declare lcd object: auto locate & auto config expander chipĬonst int LCD_ROWS = 2 //(2,1, 0, 4, 5, 6, 7, 3, POSITIVE) // Set the LCD I2C address we many end up changing it to 2, 3, 4, 5, 6, 7 instead Set the pins on the I2C chip used for LCD connections: set the LCD address to 0x3F for PCF8574AT with A0,A1,A0 address line open, default setting. hd44780_I2Cexp display(SCL,SDA) // instead of TM1637Display HI, I am using an FTDI USB to TTL Converter to program an Arduino Pro Mini with an UpTime Counter code for a 1602 BLUE LCD 16x2 HD44780 with IIC I2C Serial Interface Adapter Module Display.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |